Toshiba e-STUDIO350 Скачать руководство пользователя страница 175

Страница: 175 / 286

November 2003 © TOSHIBA TEC

9 - 25

e-STUDIO350/450 PAPER FEEDING SYSTEM

Fig. 9-462

Fig. 9-461

Fig. 9-460

Fig. 9-459

[E]

Tray drive unit/Tray-up motor

(1)

Remove the upper and lower drawers.

(2)

Take off the rear cover (

Chapter 2.5.1

[H]).

(3)

Take off the right rear hinge cover

(

Chapter 2.5.1 [D]).

(4)

Remove 4 screws and take off the right lower

cover (

Chapter 2.5.1 [E]).

(5)

Remove 4 screws and take off the noise filter

assembly.

(6)

Disconnect 1 connector of the tray drive unit and

release the harness from the harness clamp.

(7)

Remove 4 screws and take off the tray drive

unit with the plate.

(8)

Remove 4 screws and detach the tray drive

unit from the plate.

(9)

Place the unit with its coupling up and release

6 latches to take off the cover.

Note:

Be careful in taking off the cover because

there is a spring in the tray drive unit.

Screw

Connector

Tray drive
unit

Spring

Noise filter
assembly

Coupling

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 175 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: