Toshiba e-STUDIO350 Скачать руководство пользователя страница 126

Страница: 126 / 286

e-STUDIO350/450 SCANNER

6 - 18

November 2003 © TOSHIBA TEC

Notes:

1. When installing, fix the lens unit with

the screws while pushing the unit to the

rear side.

2. Refer to “3.7.2 Lens Unit” in the Service

Handbook for the adjustment method.

3. Never attempt to loosen the screws

(8 pcs.) of the lens unit denoted with

arrows.

4. Handle the unit with extra care. Do not

touch the adjusted area or lens. (Hold the

unit as shown in the figure at right.)

[E]

Lens unit

(1)

Take off the lens cover (

Chapter 6.7 [B]).

(2)

Disconnect 1 connector from the SLG board.

(3)

Remove 2 screws and take off the lens unit.

(7)

Remove 1 screw. Lift up the exposure lamp

and take it off by pulling out toward you.

Note:

Make sure to hold only the black molded part

of the exposure lamp. Do not touch any other

part than this black molded part.

Fig. 6-708

Fig. 6-709

Fig. 6-710

Fig. 6-711

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 126 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: