Toshiba e-STUDIO350 Скачать руководство пользователя страница 129

Страница: 129 / 286

November 2003 © TOSHIBA TEC

6 - 21

e-STUDIO350/450 SCANNER

[J]

Carriage wire / Carriage-2

(1)

Take off the carriage-1 (

Chapter 6.7 [G]).

(2)

Install the wire holder jig to each pulley on front

and rear sides, not to loosen the carriage wire.

Note:

Refer to “3.9 Adjustment of Carriages” in the

Service Handbook for the installation direc-

tion of the wire holder jig.

(3)

Remove the tension springs on both front and

rear sides.

(4)

Remove the carriage wires on both front and

rear sides.

(5)

Rotate the carriage-2 in the direction where

the inside of the frame is dented shown in the

figure at right, not to touch the mirror. Then

take off the carriage-2.

Fig. 6-719

Fig. 6-720

Fig. 6-721

Tension spring

[K] Mirrors-2 and -3

(1)

Take off the carriage-2 (

Chapter 6.7 [J]).

Note:

When replacing the mirrors-2 and -3, re-

place the carriage-2 together with mirrors-

2 and -3.

Mirrors-2 and -3 should not be removed.

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 129 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: