Toshiba e-STUDIO350 Скачать руководство пользователя страница 147

Страница: 147 / 286

November 2003 © TOSHIBA TEC

8 - 7

e-STUDIO350/450 LASER OPTICAL UNIT

Fig. 8-302 shows a block diagram of the semiconductive laser control circuit. The semiconductive laser

performs monitor efficiency regulation (a process to control monitor current for the light amount), and

laser itself is adjusted to initial output emission of approx. 2.11 mW (approx. 421 µW on the drum surface).

The regulated voltage of the monitor output is fed back to the laser power comparison circuit. This monitor

output voltage is compared with the laser power voltage set for the control circuit for every scanning.

Laser driver circuit increases the forward current if the laser power is insufficient, and decreases the

current when the power is excessive to maintain a constant optical output.

8.3 Laser Diode

The laser used in this equipment is a AlGaAs type semiconductive laser. It is generated in the single-

horizontal mode, and its wavelength is approx. 785 nm. This semiconductive laser outputs 5mW with

standard DC power supply. Laser intensity is controlled by using the output from the PIN diode for moni-

toring light output in the semiconductive laser.

Fig. 8-302

Fig. 8-301

Threshold current

Forward current
Monitor current

Current (mA)

Optical Output

( mW

)

Low temp.

High temp.

Regulation

The relation between the current and optical output

of the semiconductive laser is as shown at right.

Light emission is started when the forward current

reaches or becomes larger than the threshold cur-

rent and outputs the monitor current which is pro-

portionate to the optical output. The threshold cur-

rent and monitor current differs depending on each

semiconductive laser. So optical output has to be

adjusted to maintain a constant value.

Since the optical output of the semiconductive la-

ser is decreased as the temperature of the laser

rises, APC control needs to be performed to main-

tain a constant optical output.

Monitor output

Monitor effi-
ciency regula-
tion circuit

Laser power
comparison
circuit

Laser driver
circuit

Semiconductive laser

Constant
optical output

Power source

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 147 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: