Toshiba e-STUDIO350 Скачать руководство пользователя страница 211

Страница: 211 / 286

November 2003 © TOSHIBA TEC

12 - 3

e-STUDIO350/450 DEVELOPMENT SYSTEM

12.3 Drive Circuit of Toner Motor

The toner motor (brush motor) is a motor to supply toner from the toner cartridge to the developer unit.

The toner motor is driven by the transistor TA8428 (LGC board: IC51).

Circuit diagram of the toner motor

Motor driver TA8428 (IC51) is connected with both ends of the motor wire.

— When the PC6(TNRM1-1) of the ASIC GA becomes “H” and PC7 (TNRM2-1) becomes “L” levels,

current flows into the motor wire and the motor is rotated.

— When both of PC6 (TNRM1-1) and PC7 (TNRM2-1) of the ASIC GA become “H” level, the motor is

braked and stopped.

— When both of PC6 (TNRM1-1) and PC7 (TNRM2-1) of ASIC GA become “L” level, the motor waits

for the next command (the motor is stopped).

MAIN
-CPU

IC24

ASIC GA

TD62385

TA8428

PC6

Toner motor

PC7

IC21

IC38

IC51

Fig. 12-301

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 211 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: