manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

DocID025202 Rev 7

362/1080

RM0365

Analog-to-digital converters (ADC)

392

         

Bit 2

ADSTART

: ADC start of regular conversion

This bit is set by software to start ADC conversion of regular channels. Depending on the configuration 
bits EXTEN, a conversion will start immediately (software trigger configuration) or once a regular 
hardware trigger event occurs (hardware trigger configuration).
It is cleared by hardware:
– in single conversion mode when software trigger is selected (EXTSEL=0x0): at the assertion of the 

End of Regular Conversion Sequence (EOS) flag.

– in all cases: after the execution of the ADSTP command, at the same time that ADSTP is cleared by 

hardware.
0: No ADC regular conversion is ongoing.
1: Write 1 to start regular conversions. Read 1 means that the ADC is operating and eventually 
converting a regular channel.

Note: Software is allowed to set ADSTART only when ADEN=1 and ADDIS=0 (ADC is enabled and 

there is no pending request to disable the ADC)

Note: In auto-injection mode (JAUTO=1), regular and auto-injected conversions are started by setting 

bit ADSTART (JADSTART must be kept cleared)

Bit 1

ADDIS

: ADC disable command

This bit is set by software to disable the ADC (ADDIS command) and put it into power-down state 
(OFF state).
It is cleared by hardware once the ADC is effectively disabled (ADEN is also cleared by hardware at 
this time).

0: no ADDIS command ongoing
1: Write 1 to disable the ADC. Read 1 means that an ADDIS command is in progress. 

Note: Software is allowed to set ADDIS only when ADEN=1 and both ADSTART=0 and JADSTART=0 

(which ensures that no conversion is ongoing)

Bit 0

ADEN

: ADC enable control

This bit is set by software to enable the ADC. The ADC will be effectively ready to operate once the 
flag ADRDY has been set.
It is cleared by hardware when the ADC is disabled, after the execution of the ADDIS command.

0: ADC is disabled (OFF state)
1: Write 1 to enable the ADC.

Note: Software is allowed to set ADEN only when all bits of ADCx_CR registers are 0 (ADCAL=0, 

JADSTART=0, ADSTART=0, ADSTP=0, ADDIS=0 and ADEN=0) except for bit ADVREGEN 
which must be 1 (and the software must have wait for the startup time of the voltage regulator)

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Бренд: Ubiquiti Страницы: 22
NEC P401-TMX4D User Manual preview
P401-TMX4D
Бренд: NEC Страницы: 2
Rabbit RabbitCore RCM4400W Product Manual preview
RabbitCore RCM4400W
Бренд: Rabbit Страницы: 126
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Бренд: Moxa Technologies Страницы: 2
Ubiquiti LiteBeam M5-23 Quick Start Manual preview
LiteBeam M5-23
Бренд: Ubiquiti Страницы: 21
Serial Cables PCI4-AD-x16HI-BG4 User Manual preview
PCI4-AD-x16HI-BG4
Бренд: Serial Cables Страницы: 15
Forcepoint V10000 G4R2 Quick Start Manual preview
V10000 G4R2
Бренд: Forcepoint Страницы: 2
Hameg HM6050-2K Manual preview
HM6050-2K
Бренд: Hameg Страницы: 46
MACHINIST X79-Z9-D7 User Manual preview
X79-Z9-D7
Бренд: MACHINIST Страницы: 15
peplink Balance 380 User Manual preview
Balance 380
Бренд: peplink Страницы: 111
Boser HS-2621 Manual preview
HS-2621
Бренд: Boser Страницы: 54
HighPoint NA381TB Quick Installation Manual preview
NA381TB
Бренд: HighPoint Страницы: 3
Intel 80C186EC Manual preview
80C186EC
Бренд: Intel Страницы: 57
X-Micro XWL-11GPAR User Manual preview
XWL-11GPAR
Бренд: X-Micro Страницы: 24
I-Tech NW117HD-8Ke User Manual preview
NW117HD-8Ke
Бренд: I-Tech Страницы: 6
Icop VMXP-6453 User Manual preview
VMXP-6453
Бренд: Icop Страницы: 31
Faroudja DVP3000 Installation And Operation Manual preview
DVP3000
Бренд: Faroudja Страницы: 17
Faroudja DVP5000 Installation And Operation Manual preview
DVP5000
Бренд: Faroudja Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды