manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

Debug support (DBG)

RM0365

1063/1080

DocID025202 Rev 7

33.15.8 TRACECLKIN 

connection inside the STM32F302xx

In the STM32F302xx, this TRACECLKIN input is internally connected to HCLK. This means 
that when in asynchronous trace mode, the application is restricted to use to time frames 
where the CPU frequency is stable.

Note:

Important:

 when using asynchronous trace: it is important to be aware that:

The default clock of the STM32F302xx MCUs is the internal RC oscillator. Its frequency 
under reset is different from the one after reset release. This is because the RC calibration 
is the default one under system reset and is updated at each system reset release.
Consequently, the trace port analyzer (TPA) should not enable the trace (with the 
TRACE_IOEN bit) under system reset, because a Synchronization Frame Packet will be 
issued with a different bit time than trace packets which will be transmitted after reset 
release.

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Бренд: IEI Technology Страницы: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Бренд: IEI Technology Страницы: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Бренд: IEI Technology Страницы: 3
Teagle Tomahawk 7100 Operator'S Manual preview
Tomahawk 7100
Бренд: Teagle Страницы: 40
MICROENER IM30-CV Operation Manual preview
IM30-CV
Бренд: MICROENER Страницы: 24
Patton electronics ipRocketLink IAD 3086 Quick Start Manual preview
ipRocketLink IAD 3086
Бренд: Patton electronics Страницы: 12
Air Live AirVideo-100 Quick Setup Manual preview
AirVideo-100
Бренд: Air Live Страницы: 2
AES BeBoPr++ User Manual preview
BeBoPr++
Бренд: AES Страницы: 44
Lanner NCA-6520 User Manual preview
NCA-6520
Бренд: Lanner Страницы: 141
Xinje VH5 Series User Manual preview
VH5 Series
Бренд: Xinje Страницы: 76
Juniper WX 100 Quick Start Manual preview
WX 100
Бренд: Juniper Страницы: 6
H3C SecPath F50X0 Series Manual preview
SecPath F50X0 Series
Бренд: H3C Страницы: 41
Thermalright Macho Rev. A (BW) Manual preview
Macho Rev. A (BW)
Бренд: Thermalright Страницы: 32
WiebeTech FCDKV4 User Manual preview
FCDKV4
Бренд: WiebeTech Страницы: 8
Valcom VIP-997 Manual preview
VIP-997
Бренд: Valcom Страницы: 4
ADLINK Technology MCM-216 User Manual preview
MCM-216
Бренд: ADLINK Technology Страницы: 69
Arduino TC4+ Quick Start Manual preview
TC4+
Бренд: Arduino Страницы: 10
Ecolab EcoJet EcoStar 1500 Installation & Operation Manual preview
EcoJet EcoStar 1500
Бренд: Ecolab Страницы: 80

Бренды по названию

Популярные бренды

Загрузить еще бренды