manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

Analog-to-digital converters (ADC)

RM0365

387/1080

DocID025202 Rev 7

Bits 17:16

CKMODE[1:0]: 

ADC clock mode

These bits are set and cleared by software to define the ADC clock scheme (which is common 
to both master and slave ADCs):

00: CK_ADCx (x=123) (Asynchronous clock mode), generated at product level (refer to 

Section 6: Reset and clock control (RCC)

)

01: HCLK/1 (Synchronous clock mode). This configuration must be enabled only if the AHB 
clock prescaler is set to 1 (HPRE[3:0] = 0xxx in RCC_CFGR register) and if the system clock 
has a 50% duty cycle.
10: HCLK/2 (Synchronous clock mode)
11: HCLK/4 (Synchronous clock mode)

In all synchronous clock modes, there is no jitter in the delay from a timer trigger to the start of 
a conversion.

Note: Software is allowed to write these bits only when the ADCs are disabled (ADCAL=0, 

JADSTART=0, ADSTART=0, ADSTP=0, ADDIS=0 and ADEN=0).

Bits 15:14

MDMA[1:0]:

 Direct memory access mode for dual ADC mode

This bit-field is set and cleared by software. Refer to the DMA controller section for more 
details.

00: MDMA mode disabled
01: reserved
10: MDMA mode enabled for 12 and 10-bit resolution
11: MDMA mode enabled for 8 and 6-bit resolution

Note: Software is allowed to write these bits only when ADSTART=0 (which ensures that no 

regular conversion is ongoing).

Bit 13  

DMACFG:

 DMA configuration (for dual ADC mode)

This bit is set and cleared by software to select between two DMA modes of operation and is 
effective only when DMAEN=1.

0: DMA One Shot Mode selected
1: DMA Circular Mode selected

For more details, refer to 

Section : Managing conversions using the DMA

Note: Software is allowed to write these bits only when ADSTART=0 (which ensures that no 

regular conversion is ongoing).

Bit 12 Reserved, must be kept at reset value.

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Бренд: MiLAN Страницы: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Бренд: Symantec Страницы: 2
Quectel Wi-Fi-M.2 EVB User Manual preview
Wi-Fi-M.2 EVB
Бренд: Quectel Страницы: 23
Bridgeworks a204 Hardware Manual preview
a204
Бренд: Bridgeworks Страницы: 18
Arduino ABX00061 Reference Manual preview
ABX00061
Бренд: Arduino Страницы: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Бренд: Divio Страницы: 4
Commell FS-A79 User Manual preview
FS-A79
Бренд: Commell Страницы: 36
SafeHome NVR903 Manual preview
NVR903
Бренд: SafeHome Страницы: 24
National Instruments PXI PXITM -1000 User Manual preview
PXI PXITM -1000
Бренд: National Instruments Страницы: 55
Meinberg CPU-C15G2 Setup Manual preview
CPU-C15G2
Бренд: Meinberg Страницы: 14
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Бренд: Cypress Semiconductor Страницы: 31
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Бренд: HMS Страницы: 18
Safety Vision ROADRECORDER 8400 NVR User Manual preview
ROADRECORDER 8400 NVR
Бренд: Safety Vision Страницы: 27
NETGEAR ReadyNAS Duo v2 Software Manual preview
ReadyNAS Duo v2
Бренд: NETGEAR Страницы: 100
Clare Controls ClareVision CV-M161620-04 Installation Manual preview
ClareVision CV-M161620-04
Бренд: Clare Controls Страницы: 32
Cognex 800-5815-1 Installation And Reference Manual preview
800-5815-1
Бренд: Cognex Страницы: 57
Intel SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz Specification preview
SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz
Бренд: Intel Страницы: 56
ZyXEL Communications WAP6804 User Manual preview
WAP6804
Бренд: ZyXEL Communications Страницы: 114

Бренды по названию

Популярные бренды

Загрузить еще бренды