manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

DocID025202 Rev 7

414/1080

RM0365

Comparator (COMP)

422

Bit 14 Reserved, must be kept at reset value.

Bits 13:10

COMP1OUTSEL[3:0]

: Comparator 1 output selection

These bits select which Timer input must be connected with the comparator1 output. 
0000: No selection
0001: (BRK_ACTH) Timer 1 break input
0010: (BRK2) Timer 1 break input 2
0101: Timer 1 break input 2
0110: Timer 1 OCrefclear input
0111: Timer 1 input capture 1
1000: Timer 2 input capture 4
1001; Timer 2 OCrefclear input
1010: Timer 3 input capture 1
1011: Timer 3 OCrefclear input
Remaining combinations: reserved.

Note: Depending on the product, when a timer is not available, the corresponding combination is 

reserved.

Bits 9:7 Reserved, must be kept at reset value.

Bits 6:4

COMP1INMSEL[2:0]

: Comparator 1 inverting input selection

These bits allows to select the source connected to the inverting input of the comparator 1. 
000: 1/4 of Vrefint
001: 1/2 of Vrefint
010: 3/4 of Vrefint
011: Vrefint
100: PA4 or DAC1 output if enabled
101: PA5
110: PA0
111: Reserved

Bits 3:2

COMP1MODE[1:0]

: Comparator 1 mode 

These bits control the operating mode of the comparator1 and allows to adjust the 
speed/consumption.
00: High speed
01: Medium speed
10: Low-power
11: Ultra-low-power

Bit 1

COMP1_INP_DAC

: Comparator 1 non inverting input connection to DAC output.

This bit closes a switch between comparator 1 non-inverting input (PA0) and DAC out I/O (PA4).
0: Switch open
1: Switch closed

Note: This switch is solely intended to redirect signals onto high impedance input, such as COMP1 

non-inverting input (highly resistive switch).

Bit 0

COMP1EN

: Comparator 1 enable

This bit switches COMP1 ON/OFF.
0: Comparator 1 disabled
1: Comparator 1 enabled

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

D-Link DES-1210-08P Manual preview
DES-1210-08P
Бренд: D-Link Страницы: 15
Patton electronics NetLink 2960 RAS Datasheet preview
NetLink 2960 RAS
Бренд: Patton electronics Страницы: 2
Orban OPTIMOD 6300 Operating Manual preview
OPTIMOD 6300
Бренд: Orban Страницы: 255
B&B Electronics Parallel Printer Card PIOC User Manual preview
Parallel Printer Card PIOC
Бренд: B&B Electronics Страницы: 16
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Бренд: ESD Страницы: 28
Endace DAG 7.1S User Manual preview
DAG 7.1S
Бренд: Endace Страницы: 51
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Бренд: Zhone Страницы: 114
Pressalit Care Indivo RK1010 User And Maintenance Manual preview
Indivo RK1010
Бренд: Pressalit Care Страницы: 31
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Бренд: IFM Electronic Страницы: 14
Segger J-Link-OB-STM32F072-128KB User Manual preview
J-Link-OB-STM32F072-128KB
Бренд: Segger Страницы: 18
Seagate CHEETAH ST34501FC Product Manual preview
CHEETAH ST34501FC
Бренд: Seagate Страницы: 68
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Бренд: swiftech Страницы: 2
Altera Cyclone IV GX Reference Manual preview
Cyclone IV GX
Бренд: Altera Страницы: 40
Milesight Pro UR32 Quick Start Manual preview
Pro UR32
Бренд: Milesight Страницы: 15
Hanwha Techwin Wisenet PRN-6400DB4 User Manual preview
Wisenet PRN-6400DB4
Бренд: Hanwha Techwin Страницы: 125
Ciara Horizon D10750 Disassembly Manual preview
Horizon D10750
Бренд: Ciara Страницы: 14
Valcom VIP-997 Manual preview
VIP-997
Бренд: Valcom Страницы: 4
Fujitsu PRIMERGY TX150 S2 Manual preview
PRIMERGY TX150 S2
Бренд: Fujitsu Страницы: 163

Бренды по названию

Популярные бренды

Загрузить еще бренды