manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

Universal serial bus full-speed device interface (USB)

RM0365

1023/1080

DocID025202 Rev 7

Bit 11

SUSP: 

Suspend mode request

This bit is set by the hardware when no traffic has been received for 3 ms, indicating a 
suspend mode request from the USB bus. The suspend condition check is enabled 
immediately after any USB reset and it is disabled by the hardware when the suspend mode 
is active (FSUSP=1) until the end of resume sequence. This bit is read/write but only ‘0 can 
be written and writing ‘1 has no effect.

Bit 10

RESET:

 USB reset request

Set when the USB peripheral detects an active USB RESET signal at its inputs. The USB 
peripheral, in response to a RESET, just resets its internal protocol state machine, generating 
an interrupt if RESETM enable bit in the USB_CNTR register is set. Reception and 
transmission are disabled until the RESET bit is cleared. All configuration registers do not 
reset: the microcontroller must explicitly clear these registers (this is to ensure that the 
RESET interrupt can be safely delivered, and any transaction immediately followed by a 
RESET can be completed). The function address and endpoint registers are reset by an USB 
reset event. 
This bit is read/write but only ‘0 can be written and writing ‘1 has no effect.

Bit 9

SOF:

 Start of frame

This bit signals the beginning of a new USB frame and it is set when a SOF packet arrives 
through the USB bus. The interrupt service routine may monitor the SOF events to have a 
1 ms synchronization event to the USB host and to safely read the USB_FNR register which 
is updated at the SOF packet reception (this could be useful for isochronous applications). 
This bit is read/write but only ‘0 can be written and writing ‘1 has no effect.

Bit 8

ESOF:

 Expected start of frame

This bit is set by the hardware when an SOF packet is expected but not received. The host 
sends an SOF packet each 1 ms, but if the hub does not receive it properly, the

 

Suspend 

Timer issues this interrupt. If three consecutive ESOF interrupts are generated (i.e. three 
SOF packets are lost) without any traffic occurring in between, a SUSP interrupt is 
generated. This bit is set even when the missing SOF packets occur while the

 

Suspend 

Timer is not yet locked. This bit is read/write but only ‘0 can be written and writing ‘1 has no 
effect.

Bit 7

L1REQ: 

LPM L1 state request

This bit is set by the hardware when LPM command to enter the L1 state is successfully 
received and acknowledged. This bit is read/write but only ‘0 can be written and writing ‘1 has 
no effect.

Note: If LPM is not supported, this bit is not implemented and considered as reserved. Please 

refer to 

Section 32.3: USB implementation

.

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

Aastra CNX Product Brief preview
CNX
Бренд: Aastra Страницы: 2
dbx ProVocal Specifications preview
ProVocal
Бренд: dbx Страницы: 2
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Бренд: Ubiquiti Страницы: 23
DAQ system PCIe-FRM13 User Manual preview
PCIe-FRM13
Бренд: DAQ system Страницы: 41
DAQ system PCIe-SER01 User Manual preview
PCIe-SER01
Бренд: DAQ system Страницы: 19
SeaLevel 7406e User Manual preview
7406e
Бренд: SeaLevel Страницы: 17
ekwb EK-FC Installation Manual preview
EK-FC
Бренд: ekwb Страницы: 2
Aaeon SBC-657B Manual preview
SBC-657B
Бренд: Aaeon Страницы: 61
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Бренд: ANEP Страницы: 48
Kontron ePanel-C3 Technical Manual preview
ePanel-C3
Бренд: Kontron Страницы: 62
Ubiquiti airMAX NanoBridge M NBM3 Quick Start Manual preview
airMAX NanoBridge M NBM3
Бренд: Ubiquiti Страницы: 24
Tripp Lite SmartRack SR25UBEXP Specifications preview
SmartRack SR25UBEXP
Бренд: Tripp Lite Страницы: 4
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Бренд: ICP DAS USA Страницы: 31
ZALMAN OPTIMA II CNPS10X User Manual preview
OPTIMA II CNPS10X
Бренд: ZALMAN Страницы: 20
One Identity Safeguard for Privileged Sessions 3000 Installation Manual preview
Safeguard for Privileged Sessions 3000
Бренд: One Identity Страницы: 37
Hanwha Techwin WISENET XRN-1610 User Manual preview
WISENET XRN-1610
Бренд: Hanwha Techwin Страницы: 88
National Instruments PXI Express PXIe-1085 Series User Manual preview
PXI Express PXIe-1085 Series
Бренд: National Instruments Страницы: 89
HighPoint NA381TB Quick Installation Manual preview
NA381TB
Бренд: HighPoint Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды