manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

DocID025202 Rev 7

94/1080

RM0365

Peripheral interconnect matrix

96

The selection is made based on “COMPxINMSEL” bits value in “COMPx_CSR” register.

7.3.12 From 

VREFINT to COMP

Besides to the DAC channel output, Vrefint (x1, x3/4, x1/2, x1/4) can be selected as 
comparator inverting input using “COMPxINMSEL” bits in “COMPx_CSR” register.

7.3.13 

From DAC to OPAMP

In STM32F302xB/C/D/E, the DAC1 output is connected internally to OPAMP1 non-inverting 
input.

7.3.14 

From TIM to OPAMP 

The switch between OPAMP inverting and non-inverting inputs can be done automatically. 
This automatic switch is triggered by the TIM1 CC6 output arriving on the OPAMP input 
multiplexers. More details on this feature are available in 

Section 18.3.6: Timer controlled 

Multiplexer mode

.

7.3.15 From 

TIM to TIM

Some STM32F3 timers are linked together internally for timer synchronization or chaining. 

When one timer is configured in Master Mode, it can reset, start, stop or clock the counter of 
another timer configured in Slave Mode.

A description of the feature with the various synchronization modes is available in:

•

Section 20.3.25: Timer synchronization

 f

or the advanced-control timers (TIM1)

•

Section 21.3.19: Timer synchronization

 

for the general-purpose timers 

(TIM2/TIM3/TIM4)

The slave mode selection is made using “SMS” bits, as described in:

•

Section 20.4.3: TIM1 slave mode control register (TIMx_SMCR)

,

•

Section 21.4.3: TIMx slave mode control register (TIMx_SMCR)

 

for the general-

purpose timers (TIM2/TIM3/TIM4),

•

Section 22.5.3: TIM15 slave mode control register (TIM15_SMCR)

.

The possible master/slave connections are summarized in the following table providing the 
internal trigger connection:

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Бренд: ICP DAS USA Страницы: 8
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Бренд: National Instruments Страницы: 85
TFortis Teleport-1 Configuration Manual preview
Teleport-1
Бренд: TFortis Страницы: 86
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Бренд: HARTING Страницы: 13
Lanner NCA-1040 User Manual preview
NCA-1040
Бренд: Lanner Страницы: 59
NEC uPD75P3116 Datasheet preview
uPD75P3116
Бренд: NEC Страницы: 70
B&B Electronics 232PCC User Manual preview
232PCC
Бренд: B&B Electronics Страницы: 17
Dahua NVR41-4KS2 Series User Manual preview
NVR41-4KS2 Series
Бренд: Dahua Страницы: 452
ADTRAN NetVanta Analog Modem Dial Backup Interface Module Quick Start Manual preview
NetVanta Analog Modem Dial Backup Interface Module
Бренд: ADTRAN Страницы: 2
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Бренд: ZALMAN Страницы: 18
Procool SP480 Series Instructions preview
SP480 Series
Бренд: Procool Страницы: 2
Honeywell Home LTEM-PA Installation And Setup Manual preview
LTEM-PA
Бренд: Honeywell Home Страницы: 36
Cabletron Systems TRXMIM-24A User Manual preview
TRXMIM-24A
Бренд: Cabletron Systems Страницы: 56
Omnia 6FM Installation And Operation Manual preview
6FM
Бренд: Omnia Страницы: 130
VIPA System 200V PC 288 Manual preview
System 200V PC 288
Бренд: VIPA Страницы: 54
ebm-papst K3G630-FL98-02 Operating Instructions Manual preview
K3G630-FL98-02
Бренд: ebm-papst Страницы: 13
Citizen CBM-606 User Manual preview
CBM-606
Бренд: Citizen Страницы: 29
MikroTik Network Controller Manual preview
Network Controller
Бренд: MikroTik Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды