manualshive.com logo in svg

Siemens ERTEC 200P, Руководство пользователя

Siemens ERTEC 200P - это передовой сетевой коммутатор с поддержкой множества функций. Здесь вы можете бесплатно скачать руководство по эксплуатации для этого устройства. Посетите наш сайт manualshive.com, чтобы получить доступ к руководству в формате PDF.

Поделиться
Скачать
background image

 
 

 

Copyright © Siemens AG 2016. All rights reserved 

40 

ERTEC 200P-2 Manual 

Technical data subject to change 

 

Version  1.0 

 

 

A reload function cannot be provided in the primary boot loader for reading from an SPI 
flash memory as the number of addresses to be transferred is not known, and universal 
access therefore cannot be set. This must be done using the secondary boot loader. 

 

2.3.1.5.4 

Boot Mode 7 (Booting with External Host)

 

After reset, the ARM926 starts the instruction fetches from the primary boot loader. The 
basic XHIF configurations (16/32-bit bus, XHIF_ACC_MODE, XHIF_POL_RDY) are 
latched to the 

CONFIG_REG

 register after reset (see 2.3.10.9.3) and wired directly to the 

XHIF module. The parameter settings (for example page sizes, ...) at XHIF are made by 
the external host in the XHIF control registers. The ERTEC 200P signals readiness for 
firmware upload to the host with a software handshake (boot loader functionality, sema-
phore) (ready for firmware upload). At address D-TCM+0x40 (address 0x0803_0040 in 
block 3 of the D-TCM) , the OK identifier = 0x6879_9786 (software handshake) and the 
first OP code of the secondary boot loader is processed from address D-TCM+0x44 (ad-
dress 0x0803_0044 in block 3 of the D-TCM).  
Once reset is inactive, the primary boot loader also sets the XHIF interface in line with the 
ConfigPins in  the XHIF_Config  register with  the selected  XHIF_CPU_Width, 
XHIF_POL_RDY and XHIF_ACC_Mode and enables XHIF_PAGE0 with a width of 1M for 
access to the D-TCM. Other XHIF pages are not changed. The primary boot loader sets 
the address D-TCM+0x40 (address 0x0803_0040 in block 3 of the D-TCM) to 
0x0000_0000 (not OK) and waits until OK identifier = 0x6879_9786 is entered by the 
external host. 
 
SW code download from the XHIF must be actively executed by the external host pro-
cessor. The boot code can be transferred from the XHIF host to the D-TCM (block 3) of 
the ERTEC 200P. At the end of data transfer, the XHIF host sets identifier 0x6879_9786 
at address D-TCM+0x40 (semaphore address). Once the semaphore has been set, the 
ERTEC 200P maps the D-TCM to I-TCM (

TCM926_MAP

, see 2.3.10.9.14) and the sec-

ondary boot loader is started at address 0x0000_0044 (I-TCM).  Access to the I-TCM 
over XHIF is not possible; only the D-TCM can be addressed. 
 

Detection of ERTEC 200P readiness (for XHIF boot) by the external host 

For an external host processor to recognize whether the XHIF interface is ready, the 
following procedure must be observed: 
The external host polls the XHIF range register of bank 0 until the value 0x0010_0000 
(1 MByte range) appears. The reset value of the XHIF range register is 0x0000_0000. 
Access to this register is possible even during an active reset. If the external host reads 
the correct XHIF range register value (0x0010_0000), it then reads the offset for Page0, 
which must then contain the value 0x0800_0000.  The host then reads the semaphore at 
D-TCM+0x40 (address 0x0803_0040 in block 3 of the D-TCM) until it returns the value 
0x0000_0000. 
To ensure that access over XHIF to the D-TCM (block 3) is possible, the external host 
writes the address 0x0803_0044 of the D_TCM and reads back the value. If the value 
written has been read back correctly, transfer of the secondary boot loader can start. At 
the end of data transfer, the XHIF host sets identifier 0x6879_9786 at address D-
TCM+0x40 (address 0x0803_0040 in block 3 of the D-TCM)  (semaphore address). 
 

Note for module development 

Содержание ERTEC 200P






















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERTEC 200P

YASKAWA P1000 Quick Start Manual preview
P1000
Бренд: YASKAWA Страницы: 256
Jetline 9600 Series Operation Manual preview
9600 Series
Бренд: Jetline Страницы: 58
Bartlett Genesis LT3140 Technical Manual preview
Genesis LT3140
Бренд: Bartlett Страницы: 5
RBI FUTERA XLF Series Control Manual preview
FUTERA XLF Series
Бренд: RBI Страницы: 128
RBH Access Technologies UNC100 Hardware Manual preview
UNC100
Бренд: RBH Access Technologies Страницы: 36
S&C PMH Inspection Manual preview
PMH
Бренд: S&C Страницы: 11
S&C BankGuard PLUS Installation Manual preview
BankGuard PLUS
Бренд: S&C Страницы: 24
S&C BankGuard PLUS Operation preview
BankGuard PLUS
Бренд: S&C Страницы: 19
U.S. Divers Impulse Service & Repair Manual preview
Impulse
Бренд: U.S. Divers Страницы: 22
Yoshitake BSV-10F Quick Start Manual preview
BSV-10F
Бренд: Yoshitake Страницы: 4
YOKOGAWA TC 10-L Engineering Manual preview
TC 10-L
Бренд: YOKOGAWA Страницы: 20
YOKOGAWA UTAdvanced UT32A Technical Information preview
UTAdvanced UT32A
Бренд: YOKOGAWA Страницы: 3
Eaton Cutler-Hammer Jockey Instructions Manual preview
Cutler-Hammer Jockey
Бренд: Eaton Страницы: 12
Voltech ISC1000 Installation And Operating Instructions Manual preview
ISC1000
Бренд: Voltech Страницы: 8
Dantel 44093 Installation & Operation Manual preview
44093
Бренд: Dantel Страницы: 6
JCM GAMMA VERSUS Series Manual preview
GAMMA VERSUS Series
Бренд: JCM Страницы: 111
WAGO 767-4804/000-800 Manual preview
767-4804/000-800
Бренд: WAGO Страницы: 80
2N 9160341 Installation Manual preview
9160341
Бренд: 2N Страницы: 107

Бренды по названию

Популярные бренды

Загрузить еще бренды