manualshive.com logo in svg

Motortech MIC-Marine, Руководство по эксплуатации

Поделиться
Скачать
Motortech MIC-Marine Скачать руководство пользователя страница 36

5 Installation Instructions 

 

36 

Rev. 09/2019 

5.2.2

 

Installation of the Ground Strap 

  

 

1.

 

Fasten the ground strap 

 to the MIC6 ground 

pin. To do so, use one washer M6 

, one tooth 

lock washer A6 

 and one poly lock nut M6 

. 

2.

 

Connect the ground strap to one of the sides 
suitable for grounding. 

▸

 

You can wire the ignition controller as 
described in section 

Wiring of the Device

 

on page 37. 

  

 

5.3 

 

Determine the Installation Location of the Pickup 

Set the positions of the pickups depending on engine type and application. All angle reference 
information is based on: 

TDC 1st cylinder / compression cycle

 

The installation location for the pickups must have adequate mechanical strength and must not 
exceed the specified temperature ranges. The pickups are designed for the appropriate use 
only, multiple use of the pickup signal is not permissible. Ensure good accessibility to facilitate 
the calibration of the sensor. Comply with the pertinent regulations for the wire routing. 

For the exact positioning of the individual pickups, refer to the examples given in the drawings 
(see section 

Input Wiring – Pickups

 on page 42). 

 

Содержание MIC-Marine

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды