manualshive.com logo in svg

Motortech MIC-Marine, Руководство по эксплуатации

Поделиться
Скачать
Motortech MIC-Marine Скачать руководство пользователя страница 136

8 Settings via the MICT 

 

136 

Rev. 09/2019 

Warning 

Description 

Incompatible coil parameters 
received, secondary voltage 
diagnostics disabled. 

Incompatible coil parameters received. The secondary 
voltage diagnostics have been disabled. This message 
may appear during an upgrade/downgrade. Check your 
configuration data and the MICT version being used. Then 
download the configuration to the device once again. 

Invalid coil data received. 

Invalid coil data received. This message may appear 
during an upgrade/downgrade. Check your configuration 
data and the MICT version being used. Then download the 
configuration to the device once again. 

Pickup configuration invalid. 

The pickup configuration is invalid. This message may 
appear during an upgrade/downgrade. Check your 
configuration data and the MICT version being used. Then 
download the configuration to the device once again. 

Power output (

x W

) exceeded limit 

(

y W

) at a supply voltage of 

z V

. 

The power output (

x W

) exceeded warning threshold limit 

(

y W

) for longer than two minutes at a supply voltage of 

z V 

. 

Speed (

x RPM

) exceeded 

overspeed limit (

y RPM

). Previous 

speed was 

z RPM

. 

Speed (

x RPM

) exceeded overspeed limit (

y RPM

). 

Previous speed was 

z RPM 

(see 

Engine – Speed Settings

 

on page 97). The reason for this may also be an 
interference coupling on the trigger signal. 

Temperature of device (

x °C

) 

exceeded limit (

y °C

) 

The temperature of the device (

x °C

) exceeded warning 

threshold limit (

y °C

) for more than two minutes. Ensure 

that there is sufficient air circulation and/or cooling. 

  

 

8.12.6.3

 

Alarms 

Alarms can be defined in the configuration. When doing so, each alarm is assigned a 

number

 

(see 

Inputs/Outputs – Alarms

 on page 108). 

Alarm 

Description 

Alarm 

number  

"

description

" 

acknowledged. 

The alarm 

number  

"

description

" was acknowledged. 

Alarm 

number 

 "

description

" 

triggered. 

The alarm 

number  

"

description

" was triggered. 

All alarms reset. 

All alarms reset. 

  

 

Содержание MIC-Marine

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды