manualshive.com logo in svg

Motortech MIC-Marine, Руководство по эксплуатации

Поделиться
Скачать
Motortech MIC-Marine Скачать руководство пользователя страница 96

8 Settings via the MICT 

 

96 

Rev. 09/2019 

Secondary Diagnostics Enabled 

The secondary diagnosis can be deactivated and activated for ignition coils that support this 
function. If the ignition coil does not support this function, the secondary voltage estimation 
calibration and the of the secondary short calibration are not available. 

Secondary Voltage Estimation Calibration 

A correction value without units can be set for the secondary voltage estimation for every 
configured output to increase the accuracy of the secondary voltage estimation for each 
individual cylinder. This allows, for instance, different cable lengths on the engine to be 
compensated. 

The values of the secondary voltage estimation can be changed for each individual cylinder. The 
value range depends on the ignition coil. 0.0 is set as the standard value for all cylinders. You 
can adjust the secondary voltage estimation while the engine is running in the runtime 
adjustments (refer to 

Runtime Adjustments – Secondary Voltage Estimation Calibration

 on 

page 150). 

Secondary Short Detection Calibration 

The starting voltage and the secondary short detection sensitivity can be adjusted. You can 
adjust the secondary short detection in the runtime adjustments while the engine is running 
(refer to 

Runtime Adjustments – Secondary Short Calibration

 on page 151). 

Secondary Short Enable Voltage 

Set the average ignition voltage required to activate the secondary short-circuit monitoring: 

–

 

The secondary short detection is always activated at a value of 0 kV. 

–

 

The secondary short detection is always deactivated at a value of 65.535 kV. 

Secondary Short Sensitivity 

The permitted value range depends on the set ignition coil. 

Set the sensitivity of the short-circuit detection e.g. as follows: 

–

 

The sensitivity is high at a value of 0.98. 

–

 

The sensitivity is low at a value of 1.02. 

 

Содержание MIC-Marine

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды