manualshive.com logo in svg

Motortech MIC-Marine, Руководство по эксплуатации

Поделиться
Скачать
Motortech MIC-Marine Скачать руководство пользователя страница 164

9 Operation 

 

164 

Rev. 09/2019 

 

Backup the existing configuration 

Your device's configuration may be lost if the firmware update is not 
performed properly. Always backup the existing configuration via the MICT 
prior to performing an update. For more information read the section 

Working with Configurations

 on page 84. 

  
To start a firmware update, proceed as follows: 

1.

 

If an MICT is connected with the ignition controller, disconnect this connection. 

2.

 

Start the MOTORTECH Flash Tool via

 Start -> Programs -> MOTORTECH -> MOTORTECH Flash 

Tool -> x.x.x (e.g. 0.9.00003) -> MOTORTECH Flash Tool

. 

▸

 

The MOTORTECH Flash Tool will now start. 

▸

 

The software automatically checks all ports for connected devices. 

3.

 

In the 

Status

 section under 

Device

, check if your device has been recognized properly. 

▸

 

If the MOTORTECH Flash Tool does not recognize a device that is connected to your 
computer via the USB interface, you can usually still carry out a firmware update. To do 
so, observe the instructions in the information windows of the MOTORTECH Flash Tool 
for the following steps. 

4.

 

Select in area 

File

 using the 

Select

 button the desired update file. 

5.

 

By reading the displayed file information, ensure that the update file is correct for your 
device. 

6.

 

Start the update process using the 

Flash

 button or using the menu or toolbar. 

▸

 

The ignition controller is restarted automatically. 

▸

 

Now, a window opens informing you about the firmware version currently used on your 
ignition controller and also about the relevant update version. 

7.

 

Confirm with 

Yes 

to proceed with the update process. 

▸

 

Now the update will start. 

▸

 

If the firmware update was successful, you will see a relevant message. 

8.

 

After a successful firmware update, check all configuration data. 

  

 

Downgrade process 

The process for a downgrade is largely the same as the update process. You 
will only be informed that a new firmware has been installed on the device. 

   

Содержание MIC-Marine

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды