manualshive.com logo in svg

Motortech MIC-Marine, Руководство по эксплуатации

Поделиться
Скачать
Motortech MIC-Marine Скачать руководство пользователя страница 37

 

 

Rev. 09/2019 

37 

6.1 

 

Input and Output Wiring on the Controller 

  

 

Operational safety! 

All connector screws and screw joints must be adequately tightened. Refer 
to the section 

Mechanical Data

 on page 20. 

    

 

Assignment of the wire colors 

Take the assignment of the wire colors of the wiring harness for the input 
and output wiring from the wiring diagram enclosed with the wiring 
harness. 

     

 

Pay attention to the wiring diagrams 

Depending on the device version, certain signals or interfaces described in 
these instructions may not be available. You are also always to pay 
attention to the wiring diagrams enclosed with the input and output cable 
harnesses. 

  

 

6.1.1

 

Input Wiring 

The following section shows the input wiring of two device versions. Other variants of the device 
can have different connectors and pin assignments: 

–

 

Standard device version with six pickup inputs (35-pole and 26-pole input connectors) 

–

 

Device version with three pickup inputs (35-pole input connector) 

Assignment of the Connections 

The tables contains the pin assignment of the standard version of the MIC6. The device version 
with three pickup inputs has only one 35-pole input connector. 

6 Wiring of the Device 

Содержание MIC-Marine

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды