manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 78

Follow the instructions in one of the following three sections depending on whether you want to set up the port
with a static, link local, or DHCP IP Addressing mode:

–

9.5.1.  Static IP Address

–

9.5.2.  DHCP IP Address

–

9.5.3.  Link Local IP Address

9.5.1 

Static IP Address

This section describes how to provision an Ethernet port with a static IP Address.

1.

Select Static for IPv4 Method

Select 'STATIC' from the 'IPV4 METHOD' radio buttons, causing the static IP addressing settings to appear.

2.

Set IP Address

Enter a different valid IP address in the subnet your configuration PC is using.

3.

Set Gateway

If a gateway is present in your network, enter the address of your gateway. If no gateway is present the static
gateway address can be configured as 0.0.0.0.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 78

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды