manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 38

Connecting a cable into a RJ-45 port:

• If not rack mounted, place one hand on the GridTime 3000 to ensure it doesn’t move
• Gently slide the cable’s RJ-45 plug into the port. Ensure the orientation of the plug aligns with the orientation of

the port.

• Connect the other end of the cable into the relevant port in your network.
• Ensure the port is enabled in software. Once enabled, check it’s left-hand LED when directly facing the front-

panel (enabled LED), is illuminated solid green.

• The right LED (ACT LED) will flash orange as traffic passes through if the cable’s network link has successfully

been established.

Figure 6-9. RJ-45 Port

Removing a cable from a RJ-45 port:

• If not rack mounted, place one hand on the GridTime 3000 to ensure it doesn’t move
• with the other hand, press down on the flap on cable’s the RJ-45 plug
• gently slide the RJ-45 plug out of the port.

6.6.2.1.3  Eth3- Eth10 (SFP and SFP+ Ports)

This section describes how to connect to Eth3-Eth10 on the GridTime 3000.

The SFP ports support direct attach cables (DAC cables), optical and copper SFP transceivers, and up to 1G
transmission speeds. The SFP+ ports support direct attach cables, optical and copper SFP transceivers, and up to
10G transmission speeds.

Only the direct attach cables and SFP transceivers in 

Recommended SFP transceivers

 are officially recommended

and supported for use with the GridTime 3000. Other cables and SFP transceivers can be used, but they may cause
the device to be unable to meet its timing performance ratings. Assistance from Microchip support in debugging
issues related to unsupported SFPs cannot be guaranteed. Contact Microchip technical support for the most up to
date list of supported direct attach cables and SFP transceivers.

Table 6-4. Supported SFP Transceivers

Brand

Model Number

Finisar

FTLF1217P2BTL

ROBOfiber

SFP-5000-RJ45

FS

SFP-100FX-31

FS

SFP-FB-GE-T

FS

SFP-GB-GE-T

 

Installation

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 38

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды