Microchip Technology GridTime 3000 Скачать руководство пользователя страница 33

Страница: 33 / 302

Table 6-1. Power Supply Voltage and Current Range

Power Supply

Ratings

Low voltage

(DC Only)

24 Vdc -120 Vdc

2.92 A - 580 mA

High voltage

DC Ratings

120 Vdc - 250 Vdc

590 mA - 280 mA

AC Ratings

100 Vac - 240 Vac

700 mA - 292 mA

6.5.2.3

Connectors

This section describes the connectors used with the GridTime 3000's power supplies.

Table 6-2. Power Supply Connectors

Power Supply

Low Voltage

High Voltage

Connector Image

Connector Type

AMP Universal MATE-N-LOK

IEC 320-C14

Mating Connector

Molex HCS-125

Mating Connector Crimps

Molex 0018121222

Not Applicable

Crimp tool

Molex 638191100

Not Applicable

Instructions for crimping the low voltage DC connector can be found in the

14.1. Crimping the DC Connector

section.

Instructions for crimping the high voltage AC/DC connector can be found in the

14.2. Crimping the AC Connector

section.

6.5.2.4

Fuses

This section describes the fuses supplied with the GridTime 3000.

The fuses for the power supplies are located on the power supply circuit boards. Each supply has two fuses; one
larger fuse on the input to the power supply module and one on the output of the module.

Important:

This port may be connected to supply voltages up to 250V DC and/or 230V AC if it is a high

voltage (HV) PSU.

Installation

2022 Microchip Technology Inc.

and its subsidiaries

Manual

DS00004572A-page 33

Содержание GridTime 3000















































































































































































































































































































Результаты поиска

Содержание GridTime 3000

Отзывы:

Бренды по названию

Популярные бренды

Microchip Technology GridTime 3000, Руководство по установке

Результаты поиска

Содержание GridTime 3000

Отзывы:

Бренды по названию

Популярные бренды