manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 39

...........continued

Brand

Model Number

FS

SFP-10GSR-85

FS

SFP-10GLR-31

FS

SFP-PC03

Bel

SFP-1GBT-06

Bel

SFP-1GBT-09

SFP and Cable Recommendations:

• ensure your cables and SFPs support the link speeds you are using.
• follow manufacturer recommendations for correct use of cables and SFP transceivers
• If SFP+ ports are going to be run at 10G speeds, use suitable Direct Attach Copper (DAC) cables or fiber SFP

transceivers, do not use copper SFP transceivers as these may create thermal issues.

Network device recommendations

• ensure all relevant network ports can auto-negotiate link speed.
• ensure all network switches in the path support the timing protocol (NTP or PTP) you plan to use.

For SFP Ports:

Ensure all relevant network ports support one of the following:

• 10BASE-T transmission
• 100BASE-T transmission
• 1000BASE-T transmission

For SFP+ Ports:

Ensure all relevant network ports support one of the following:

• 10BASE-T transmission
• 100BASE-T transmission
• 1000BASE-T transmission
• 10G BASE-T transmission.

Figure 6-10. SFP Port

Connecting a cable into a SFP port:

1.

For copper and fiber SFP transceivers:

– Remove any rubber protection from inside the SFP’s bore(s)
– Ensure the SFP’s clasp is closed
– If not rack mounted, place one hand on the GridTime 3000 to ensure it doesn’t move
– Align the SFP with the receptacle. The SFP's product label should be face up for the top row of ports, and

face down for the bottom row of ports

 

Installation

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 39

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды