manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 104

2.

Follow the instructions in one of the following sections depending on your desired PTP Clock Mode:

–

9.5.7.2.1.  End to End Default Profile Auto Mode

–

9.5.7.2.2.  End to End Default Profile Server Only Mode

–

9.5.7.2.3.  End to End Default Profile Client Only Mode

PTP Clock Mode Descriptions

Auto mode allows the port to operate either in the server or client state depending on whether the GridTime 3000 is
in sync or not. When the GridTime 3000 is in sync or in holdover, the port will be in the server or passive server state,
when the GridTime 3000 is out of sync the port will be in the client state.

In server only mode, the port will always either be in the server or passive server state depending on whether it has
won the BMCA .

In client only mode, the port will always be in the client or listening state depending on whether there is a PTP server
available to sync to.

9.5.7.2.1  End to End Default Profile Auto Mode

This section describes how to provision a PTP End to End Default Profile Auto Mode Clock.

1.

Select Auto for PTP Clock Mode

Select 'Auto' from the 'PTP CLOCK MODE' dropdown.

2.

Select Network Protocol

Select the network protocol PTP will operate on using the 'NETWORK PROTOCOL' dropdown.

The Network protocol should be consistent across the network subnet. The supported options are IPv4 (layer
4) and PTP over Ethernet (layer 2). By default the network protocol is set to IPv4 (UDP).

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 104

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды