Microchip Technology GridTime 3000 Скачать руководство пользователя страница 236

Страница: 236 / 302

Weight

3.76kg

Ingress Protection

IP40

Enclosure

Aluminum, Painted and anodized

LCD Display

80x15mm

12.5

Factory Default Settings

This section describes the factory default settings.

Table 12-2. Factory Default Settings

Port

Description

Function

LCD Screen 

Real-time clock status

• Clock information and time
• Alarm states
• Sync states
• Firmware version 

Alarm LED Indicator

Alarm condition

• Red LED for alarm condition

Sync LED Indicator

Sync state

• Green LED for sync state

Navigation Buttons

Screen navigation and safe
shutdown of unit

• Left/Right buttons to scroll LCD

screen

• Centre button for safe

shutdown/reboot

Ethernet Administration Port

GridTime 3000 configuration and
administration

• DHCP enabled
• SNMP disabled by default

USB Administration Port

GridTime 3000 configuration and
administration

• DHCP enabled

(Will act as DHCP Server)

RJ-45 Ethernet Timing Ports

Eth 1:

• DHCP enabled
• NTP — Disabled by default
• PTP — Disabled by default 

Eth 2:

• DHCP enabled
• NTP — Disabled by default
• PTP — Disabled by default

Appendix A: Specifications

2022 Microchip Technology Inc.

and its subsidiaries

Manual

DS00004572A-page 236

Содержание GridTime 3000















































































































































































































































































































Результаты поиска

Содержание GridTime 3000

Отзывы:

Бренды по названию

Популярные бренды

Microchip Technology GridTime 3000, Руководство по установке

Результаты поиска

Содержание GridTime 3000

Отзывы:

Бренды по названию

Популярные бренды