manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 129

2.

Follow the instructions in one of the following sections depending on your desired PTP Clock Mode:

–

9.5.7.5.1.  61850-9-3 Power Utility Profile Auto Mode

–

9.5.7.5.2.  61850-9-3 Power Utility Profile Server Only Mode

–

9.5.7.5.3.  61850-9-3 Power Utility Profile Client Only Mode

PTP Clock Mode Descriptions

Auto mode allows the port to operate either in the server or client state depending on whether the GridTime 3000 is
in sync or not. When the GridTime 3000 is in sync or in holdover, the port will be in the server or passive server state,
when the GridTime 3000 is out of sync, the port will be in the client state.

In server only mode, the port will always either be in the server or passive server state depending on whether it has
won the BMCA or not.

In client only mode, the port will always be in the client or listening state depending on whether there is a PTP server
available to sync to.

9.5.7.5.1  61850-9-3 Power Utility Profile Auto Mode

This section describes how to provision a PTP 61850-9-3 Power Utility Profile Auto Mode Clock.

1.

Select Auto for PTP Clock Mode

Select 'Auto' from the 'PTP CLOCK MODE' dropdown.

2.

Network Protocol

By default, the 'NETWORK PROTOCOL' is set to Layer 2 (Ethernet), which will send packets via the Ethernet
data layer

3.

Select Operating Mode

Select the operating mode for the PTP network from the 'OPERATING MODE' dropdown.

Operating mode is a network wide parameter. The configurable options are 'One Step' or 'Two Step'.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 129

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды