manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 72

Important: 

Make sure that the IP address you choose is in subnet with your PC prior to saving the settings. If
you are accessing the CMT via the Admin Ethernet port, once the address has been set you will
have to log back into the CMT using the new address as your URL. If the new address is out of
subnet with your PC's port, you won't be able to access the CMT via the GridTime 3000's Admin
Ethernet port until you change your PC's IP address to be in subnet.

If this happens by mistake, you can also use the Admin USB-C port to log back into the CMT and
change the IP address of the Admin Ethernet port to an in subnet address.

3.

Set Gateway

By default the gateway address is set to 192.168.1.1. If a gateway is present in your network, modify the
static gateway setting to your gateway address. If no gateway is present the static gateway address can be
configured as 0.0.0.0.

4.

Set Netmask

By default the netmask is set to 255.255.255.0. If your network requires a different netmask, modify the static
netmask setting as required. By combining the netmask and static IP address you have configured, you can
validate that your network and host addresses are correct for your network.

5.

Network Name

If required, the network name can be modified if by typing the new name into the 'NETWORK NAME' textbox.
This field will set the hostname of the port.

By default, the network name will be 'gt3k-admin'.

6.

Save Settings

Click the 'SAVE' button to write the settings to the GridTime 3000.

A 'Saved!' notification will appear in the bottom right corner of the page, indicating that the settings have
successfully been written to the GridTime 3000.

9.4.2 

DHCP IP Address

This section describes how to provision the Admin Ethernet Port with a DHCP IP Address.

1.

Set DCHP IP Addressing Mode

By default, the Admin Ethernet port's IP addressing mode is set to DHCP. If changed to another mode, to set it
back to DHCP, select 'DHCP' from the 'IPV4 METHOD' radio buttons.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 72

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды