manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 147

Follow the steps below to configure the GridTime 3000 for GNSS time synchronization.

1.

Navigate to the GNSS Settings Window

Figure 9-3. GNSS Configuration Tab

3. GNSS Settings

Window will Appear

2. Click Here to 

Bring Up 

GNSS Settings 

Window

1. Click Here to 

Bring Up 

GNSS Configuration Tab

2.

Enable GNSS Receiver

Select 'ENABLE' for the 'ENABLE GNSS RECEIVER' setting.

3.

Set Mask Angle

The 'MASK ANGLE' threshold setting defines the minimum required elevation angle of GNSS satellites above
the horizon when viewed from the antenna's current position. This angle is commonly referred to as elevation,
and ranges from 0° - on the horizon, to 90° - directly overhead.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 147

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды