manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 212

The 'OFFSET HOURS FROM UTC' and 'OFFSET MINUTES FROM UTC' should be entered as the offset
between local time and UTC. Test Mode will automatically compensate for the offset and compute UTC for its
internal time.

10.3 

Changing Password

This section describes how a non-administrator user can change their password on the GridTime 3000

1.

Log in to the CMT dashboard —see 

9.2.  Logging In and Out

2.

Click the 'Change Password' icon

3.

Enter the current user's password into the 'CURRENT PASSWORD' textbox. Enter the desired new password
into the 'NEW PASSWORD' and 'CONFIRM PASSWORD' textboxes. Then click the blue ' SET PASSWORD'
button to confirm the change.

 

Operating

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 212

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды