Microchip Technology GridTime 3000 Скачать руководство пользователя страница 58

Страница: 58 / 302

Provisioning

This chapter describes how to provision the GridTime 3000. This should be followed after the GridTime 3000 has
been installed (

6. Installation

) and (

6.6. Signal Connections

) have been complete.

9.1

Establishing a Connection to the GridTime 3000

This section describes how to establish a connection to the GridTime 3000.

To provision the GridTime 3000, a connection must be established between a PC and the GridTime 3000's admin
USB-C or admin Ethernet port.

For step-by-step guidance on this, see

6.6.1. Admin Port Connections

For guidance on how to access and log into the GridTime 3000's Clock Management Tool (CMT) see the following
section.

9.2

Logging In and Out

This section describes how to log in and out of the GridTime 3000's Clock Management Tool (CMT).

Open the GridTime 3000's Clock Management Tool (CMT) by typing the IP address of a connected admin
port into a web browser on a connected PC. See

9.1. Establishing a Connection to the GridTime 3000

if a

connection is not already established between a PC and one of the GridTime 3000's admin ports.

If the correct IP address was entered, the CMT login screen should appear.

Note:

The current IP address of the administration ports can be viewed on the front LCD.

Enter the login username and password for the GridTime 3000 unit and click 'login'.

Provisioning

2022 Microchip Technology Inc.

and its subsidiaries

Manual

DS00004572A-page 58

Содержание GridTime 3000















































































































































































































































































































Результаты поиска

Содержание GridTime 3000

Отзывы:

Бренды по названию

Популярные бренды

Microchip Technology GridTime 3000, Руководство по установке

Результаты поиска

Содержание GridTime 3000

Отзывы:

Бренды по названию

Популярные бренды