manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 145

Select 'IPv4(UDP)' from the 'NETWORK PROTCOL' dropdown as shown. It is the only option available to
G.8265.1 peers, but the GridTime 3000 Ethernet port will not operate as a G.8265.1 client unless this option is
selected.

Add the IP address of the server to the 'UNICAST PEER IP ADDRESS' section. The GridTime 3000 will send
signaling messages to this IP address requesting announce and sync messages.

12.

Configure the G.8265 Priority

Enter the desired priority into the 'G8265 PRIORITY' box.

13.

Configure the Delay Mechanism

The G.8265.1 PTP profile only supports the End-to-End delay mechanism. Select this item from the drop-down
as shown. This is the only option available, but the GridTime 3000 Ethernet port will not operate as a G.8265
client unless this setting is selected.

14.

Configure the Sync Interval, Announce Interval, and Delay Interval

These settings control the interval at which the G.8265.1 server will send the associated packets. All of these
fields will take values from -7 to 4 seconds.

The units for these fields are in units 2

^n

. For example, if '-2' is entered into one of these fields, then the server

will send the associated message every 0.5 seconds.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 145

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды