manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 65

c.

Setup Daylight Savings End

If your regional daylight savings time ends on a specific instance of a weekday, select 'INSTANCE OF
WEEKDAY' in the ' DAYLIGHT SAVINGS ENDS ON' radio-buttons and go to step 

3.3.1

. If your daylight

savings time ends on a fixed date, select 'FIXED DATE' and go to step 

3.3.2

.

i.

Setup Daylight Savings Ends Instance of Weekday

In the ' DAYLIGHT SAVINGS ENDS ON INSTANCE OF WEEKDAY' settings, configure the 'DAY OF
WEEK' and 'INSTANCE OF DAY IN MONTH' daylight savings time ends, and the ' TIME OF DAY '
when this occurs in hours and minutes from midnight.

For example, if the GridTime 3000 was being installed in Denver Colorado, where daylight savings
currently ends on the 1st Sunday of November at 2.00 am, you would configure the following
settings.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 65

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды