manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 230

6.

Identify the power supply(s) you wish to replace.

7.

Remove the cables for the mains and internal cabling connectors to the power supply you wish to replace.

8.

Remove the old PSU module, and connect the mains and internal cabling connectors to the new PSU module
in the same position and orientation as when you removed them.

DANGER

If cables are damaged before or during the replacement of the power supplies, do not connect
power and contact Microchip technical support 

11.10.  Contacting Technical Support

Note: 

 Ensure the internal cable connector is oriented so the bevel is on the top, before inserting the

connector.

9.

Hold the new PSU module in place, and carefully flip over the GridTime 3000 unit. Replace the screws holding
the PSU module in place.

 

Maintenance and Troubleshooting

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 230

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды