manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 161

9.8.1.1 

Unmodulated IRIG-B Output

This section describes how to provision a GridTime 3000 pulse port to output unmodulated IRIG-B.

Note: 

 The unmodulated IRIG-B output provisioning process is the same for all BNC ports, the ST Fiber outputs,

and the HV MOSFET port. The screenshots in this section will use port 3 - a fixed frequency/DCLS BNC port, as an
example.

1.

Navigate to Port's Window

Navigate to the window for the port you want to configure by clicking on the port's corresponding icon, then
clicking the settings bar corresponding to the port.

1. Click Here to

Bring Up Port 

Configuration Tab

2. Click Here to

Bring Up

Port Window

3. Port Window 

will Appear

2.

Enable Port

Select 'ENABLE' for the enable/disable port setting.

3.

Select Pulse Output

Select 'IRIG-B DCLS' (Unmodulated IRIG-B for ST Fiber outputs) from the 'PULSE OUTPUT' dropdown.

4.

Select Signal Inversion

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 161

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды