manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 84

Note: 
Configure Port B PTP Delay Asymmetry (If Applicable)

If the delay asymmetry of the PRP Port B is known and the user is configuring PRP to use PTP, the
delay asymmetry can be entered in the PTP tab of Eth 01 in the 'PRP SECONDARY (PRP PAIR) DELAY
ASYMMETRY' number box as shown in 

Secondary Eth Port Delay Asymmetry

.

Figure 9-2. Secondary Eth Port Delay Asymmetry

4.

Save Settings

Click the 'SAVE' button to write the settings to the GridTime 3000.

A 'Saved!' notification will appear in the bottom right corner of the page, indicating that the settings have
successfully been written to the GridTime 3000.

9.5.5 

Provisioning VLAN Settings

This section describes how to provision VLAN use on a GridTime 3000 Ethernet Port.

1.

Enable VLAN Tagging

To enable VLAN tagging, navigate to the port's VLAN Settings tab. Select enable VLAN from the 'Enable
VLAN' radio buttons.

Once enabled, VLAN tags will be applied to all outgoing traffic from the port including NTP and PTP.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 84

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды