manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 75

3.

Network Name

If required, a unique hostname can be given to the admin Ethernet port by entering it into the 'NETWORK
NAME' textbox. This field will set the hostname of the port.

By default, the hostname is 'gt3k-admin'.

4.

Save Settings

Click the 'SAVE' button to write the settings to the GridTime 3000.

A 'Saved!' notification will appear in the bottom right corner of the page indicating that the settings have
successfully been written to the GridTime 3000.

9.4.3 

Link Local IP Address

This section describes how to provision the Admin Ethernet Port with a Link Local IP Address.

1.

Set IP Addressing Mode to Link Local

Select 'LINK_LOCAL' from the 'IPV4 METHOD' radio buttons to set the IP addressing mode to link local.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 75

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды