manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 158

5.

Select Transmitter Impedance Matching

Select the correct transmitter impedance matching from the 'TRANSMITTER IMPEDANCE MATCHING'
dropdown. By default, the 'TRANSMITTER IMPEDANCE MATCHING' is set to 110ohm.

6.

Enable or Disable SSM Bits

Enable or disable SSM bits in the output signal using the 'SSM BITS' radio buttons.

7.

Select Override SSM Behaviour

Select the override SSM value from the 'OVERRIDE SSM' dropdown.

8.

Save Settings

Click the 'SAVE' button to write the settings to the GridTime 3000.

A 'Saved!' notification will appear in the bottom right corner of the page indicating that the settings have
successfully been written to the GridTime 3000.

9.7.3 

Provisioning E1 Output

This section describes how to provision a T1/E1/J1 Port to output a E1 signal.

1.

Select Output

Select 'E1' from the 'SELECT OUTPUT' dropdown. This will reveal the E1 specific configuration options.

Note: 

 As the T1/E1/J1 ports must both output the same signal type (T1, J1, or E1), the signal output type for

both ports is only configurable in the port 1 configuration window.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 158

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды