manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 81

3.

PRP and VLANs

– To provision PRP on the port, see 

9.5.4.  Provisioning PRP

.

– To provision VLAN use on the port, see 

9.5.5.  Provisioning VLAN Settings

.

4.

PTP and NTP

– To provision PTP on the port, see 

9.5.7.  Provisioning PTP

.

– To provision NTP on the port, see 

9.5.6.  Provisioning NTP

.

9.5.3 

Link Local IP Address

This section describes how to provision an Ethernet port with a link local IP Address.

1.

Select Link Local for IPv4 Method

Select 'LINK_LOCAL' from the 'IPV4 METHOD' radio buttons.

2.

Network Name

If necessary, the network name can be modified if by typing the new name into the 'NETWORK NAME' textbox
under the 'ADVANCED SETTINGS' dropdown.

This field will set the hostname of the port.

The default network name will be 'gt3k-time[port number]'.

3.

PRP and VLANs

– To provision PRP on the port, see 

9.5.4.  Provisioning PRP

.

– To provision VLAN use on the port, see 

9.5.5.  Provisioning VLAN Settings

.

4.

PTP and NTP

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 81

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды