ITT HT 3196 i-FRAME Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 148

background image

228A

134

370D

423

370C

Assemble the frame

1. Support the frame assembly in a horizontal position.
2. Check the shaft-end play by moving the shaft forward and backward by hand, and note any indicator

movement.
If the total indicator reading is greater than the values in this table, then disassemble the shaft and
determine the cause.
Use this table as a reference for shaft-end play values.

Table 14: Shaft-end play

Frame

Double row bearing

Duplex bearing

STi inches (millimeters)

0.0011 (0.028)
0.0019 (0.048)

0.0007 (0.018)
0.0010 (0.025)

MTi inches (millimeters)

0.0013 (0.033)
0.0021 (0.053)

0.0009 (0.023)
0.0012 (0.030)

LTi inches (millimeters)

Not applicable

0.0010 (0.025)
0.0015 (0.038)

XLT-i inches (millimeters)

0.0014 (0.036)
0.0023 (0.058)

0.0010 (0.025)
0.0015 (0.038)

SCALE

0.160

3. Check the shaft-sleeve (126) runout.

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

105

«
...
105
106
107
108
109
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: salmson Страницы: 16

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: Zip Страницы: 16

Бренд: Midea Страницы: 36

Бренд: ProMinent Страницы: 20

Бренд: EMI Страницы: 5

Aeromax Piscine 10

Бренд: Thermor Страницы: 32

Бренд: A.O. Smith Страницы: 43

Бренд: Durapac Страницы: 11

Бренд: KNF Страницы: 88

Бренд: Annovi Reverberi Страницы: 4

Бренд: Lincoln Страницы: 16

Бренд: Oprema Страницы: 8

Бренд: Pro-Source Страницы: 24

Copper Cricket 1B

Бренд: Sage Advance Corp Страницы: 67

Бренд: Barnes Страницы: 26

Бренд: German pool Страницы: 20

CENTRO-MATIC 85430

Бренд: Lincoln Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды