ITT HT 3196 i-FRAME Скачать руководство пользователя страница 109

Страница: 109 / 148

370B

496B

108

360D

c) Install the dowel pins (469B) and bolts (370B). Tighten the bolts in a criss-cross pattern according

to the specifications in the bolt torque values table.

d) Rotate the shaft 360º to check the adapter fit.

If the total indicator reading is greater than 0.005 in. (0.13 mm), then determine the cause and
correct it before you proceed.

7. Install the labyrinth oil-seal (333A) into the adapter (108) and the bearing frame (228).

The labyrinth oil seal is an O-ring fit.

8. Position the labyrinth oil-seal drain slots at the bottom (6 o’clock) position.

Refer to Assemble the INPRO labyrinth oil-seal for more information on the labyrinth oil-seal
installation.

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

107

Содержание HT 3196 i-FRAME





















































































































































Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT HT 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды