ITT HT 3196 i-FRAME Скачать руководство пользователя страница 73

Страница: 73 / 148

Seal-chamber cover removal

Seal-chamber removal procedures

Choose from one of these procedures to remove the seal-chamber cover.

Table 9: Procedures for seal-chamber cover removal by model

Model

Procedure

3196, CV 3196, HT 3196, LF 3196, 3796

Remove the seal-chamber cover.

NM 3196, 3198

Remove the seal-chamber cover and/or backplate.

Remove the seal-chamber cover (3196, CV 3196, HT 3196, LF 3196, 3796)

1. Remove the gland stud nuts (355).
2. Remove the seal-chamber stud nuts (370H).
3. Remove the seal chamber (184).

184

355

250

370H

4. Remove the shaft sleeve (126) if it is used.

The mechanical seal is attached to the sleeve.

NOTICE: Be careful with the stationary portion of the mechanical seal that is either clamped
between the backplate and the gland or seated in the seal-chamber bore. Failure to do so may result in
equipment damage.

5. Remove the rotary portion of the seal from the sleeve by loosening the setscrews and sliding it off the

sleeve.
Refer to the mechanical-seal instructions for more information.

6. Remove the gland (250), the stationary portion of the seal, and the O-ring (360Q).

126

383

360Q

383

250

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание HT 3196 i-FRAME





















































































































































Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT HT 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды