ITT HT 3196 i-FRAME Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 148

background image

Piping guidelines

Guidelines for piping are given in the Hydraulic Institute Standards available from the Hydraulic Institute
at 9 Sylvan Way, Parsippany, NJ 07054-3802. You must review this document before you install the pump.

Checklist

Check

Explanation/comment

Checked

Check that all piping is

supported independently of, and

lined up naturally with, the pump

flange.

This helps to prevent:
• Strain on the pump
• Misalignment between the pump and the drive unit
• Wear on the pump bearings and the coupling
• Wear on the pump bearings, seal, and shafting

Keep the piping as short as

possible.

This helps to minimize friction losses.

Check that only necessary fittings

are used.

This helps to minimize friction losses.

Do not connect the piping to the

pump until:
• The grout for the baseplate or

sub-base becomes hard.

• The hold-down bolts for the

pump and the driver are
tightened.

—

Make sure that all the piping

joints and fittings are airtight.

This prevents air from entering the piping system or

leaks that occur during operation.

If the pump handles corrosive

fluids, make sure that the piping

allows you to flush out the liquid

before you remove the pump.

—

If the pump handles liquids at

elevated temperatures, make sure

that the expansion loops and

joints are properly installed.

This helps to prevent misalignment due to linear

expansion of the piping.

Installation

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

35

«
...
35
36
37
38
39
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Zoeller Страницы: 4

Бренд: Mallory Страницы: 7

Бренд: Gardena Страницы: 16

Бренд: Gardena Страницы: 9

Бренд: Gardena Страницы: 11

13000 aquasensor

Бренд: Gardena Страницы: 14

Nessie Plug&Spray NPS 1CS

Бренд: Danfoss Страницы: 12

Бренд: IMO Страницы: 24

Бренд: A.O. Smith Страницы: 44

Бренд: Barmesa Pumps Страницы: 42

Бренд: FUXTEC Страницы: 4

Бренд: Echelon Страницы: 8

Бренд: salmson Страницы: 16

Goulds AquaBoost Advanced

Бренд: Xylem Страницы: 36

Бренд: Enertech Страницы: 40

Бренд: Wayne Страницы: 1

Бренд: Debem Страницы: 68

Corken Z-Series

Бренд: Idex Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды