ITT HT 3196 i-FRAME Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 148

background image

Environmental safety

The work area

Always keep the station clean to avoid and/or discover emissions.

Waste and emissions regulations

Observe these safety regulations regarding waste and emissions:

• Appropriately dispose of all waste.
• Handle and dispose of the processed liquid in compliance with applicable environmental regulations.
• Clean up all spills in accordance with safety and environmental procedures.
• Report all environmental emissions to the appropriate authorities.

Electrical installation

For electrical installation recycling requirements, consult your local electric utility.

Recycling guidelines

Always follow local laws and regulations regarding recycling.

User safety

General safety rules

These safety rules apply:

• Always keep the work area clean.
• Pay attention to the risks presented by gas and vapors in the work area.
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash hazards.
• Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

Safety equipment

Use safety equipment according to the company regulations. Use this safety equipment within the work
area:

• Helmet
• Safety goggles, preferably with side shields
• Protective shoes
• Protective gloves
• Gas mask
• Hearing protection
• First-aid kit
• Safety devices

NOTICE:
Never operate a unit unless safety devices are installed. Also see specific information about safety
devices in other chapters of this manual.

Electrical connections

Electrical connections must be made by certified electricians in compliance with all international, national,
state, and local regulations. For more information about requirements, see sections dealing specifically with
electrical connections.

Precautions before work

Observe these safety precautions before you work with the product or are in connection with the product:

• Provide a suitable barrier around the work area, for example, a guard rail.
• Make sure that all safety guards are in place and secure.
• Make sure that the equipment is properly insulated when it operates at extreme temperatures.
• Allow all system and pump components to cool before you handle them.
• Make sure that you have a clear path of retreat.

Introduction and Safety

6

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
6
7
8
9
10
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Eccotemp Страницы: 56

Бренд: Daikin Страницы: 60

VeroLine-IPS 20

Бренд: Wilo Страницы: 42

Бренд: Gardena Страницы: 10

Tranquility Low-Profile Series

Бренд: ClimateMaster Страницы: 76

Бренд: IWAKI PUMPS Страницы: 64

Бренд: Rheem Страницы: 1

UFLEX SilverSteer UP25 F-SVS

Бренд: Ultraflex Страницы: 29

SBC 1100 ADV PLUS FR

Бренд: Quick Страницы: 76

Бренд: hajdu Страницы: 132

Бренд: K&T Страницы: 17

Бренд: Wacker Neuson Страницы: 52

Бренд: Glen Dimplex Страницы: 40

Бренд: XtremepowerUS Страницы: 14

Бренд: Wilo Страницы: 16

Бренд: Wilo Страницы: 32

ULTRA-FLO MY3-50 METAL Series

Бренд: Q-MAX Страницы: 12

Бренд: AL-KO Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды