ITT HT 3196 i-FRAME Скачать руководство пользователя страница 88

Страница: 88 / 148

Surface inspection locations

This figure shows the areas to inspect for wear on the bearing frame outside surface.

228

Figure 20: Outside surface inspection locations

This figure shows the areas to inspect for wear on the bearing frame inside surface.

241

Figure 21: Inside surface inspection locations

C-face adapter inspection

Checklist

• Visually inspect the C-face adapter (340) for cracks.
• Check all surfaces for rust, scale, or debris and remove all loose and foreign material.
• Check for corrosion or pitting.

This figure shows the areas to inspect for cracks on the C-face adapter.

Figure 22: C-face adapter inspection locations

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание HT 3196 i-FRAME





















































































































































Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT HT 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды