ITT HT 3196 i-FRAME Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 148

background image

Service temperature

STi

MTi/LTi

XLT-i

in. (mm)

in. (mm)

in. (mm)

Up to 650°F (343°C)

0.016 (0.40)

0.019 (0.48)

0.026 (0.66)

Up to 700°F (371°C)

0.017 (0.43)

0.020 (0.50)

0.027 (0.69)

Impeller-clearance setting

Importance of a proper impeller clearance

A proper impeller clearance ensures that the pump runs at high performance.

WARNING:

• The impeller clearance setting procedure must be followed. Improperly setting the clearance or not

following any of the proper procedures can result in sparks, unexpected heat generation, and
equipment damage.

• If you use a cartridge mechanical seal, you must install the centering clips and loosen the set screws

before you set the impeller clearance. Failure to do so could result in sparks, heat generation, and
mechanical seal damage.

Impeller clearance methods

You can set the impeller clearance with either of these methods:

• Dial indicator method
• Feeler gauge method

Set the impeller clearance - dial indicator method (all except CV 3196)

WARNING:
Always disconnect and lock out power to the driver before you perform any installation or maintenance
tasks. Failure to disconnect and lock out driver power will result in serious physical injury.

1. Remove the coupling guard.
2. Set the indicator so that the button contacts either the shaft end or the face of the coupling.

228

134A

423

370C

370D

3. Loosen the jam nuts (423) on the jack bolts (370D) , and then back the bolts out about two turns.
4. Tighten the locking bolts evenly (370C), bringing the bearing housing (134A) towards the frame (228)

until the impeller contacts the casing.

Commissioning, Startup, Operation, and Shutdown

44

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
44
45
46
47
48
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: DAB Страницы: 8

Бренд: Nakayama Страницы: 8

geoTHERM SERIES

Бренд: Vaillant Страницы: 112

geoTHERM SERIES

Бренд: Vaillant Страницы: 132

Бренд: TapFlo Страницы: 63

Бренд: MasterCraft Страницы: 8

SUBMERSIBLE DIRTY WATER PUMP 93819

Бренд: Pacific hydrostar Страницы: 14

Бренд: Zodiac Страницы: 32

Бренд: Barnes Страницы: 18

GOULDS 45HB-70HB

Бренд: Xylem Страницы: 12

MICROPUMP 668-400-2

Бренд: Idex Страницы: 33

Gast 1HAB-25 Shown

Бренд: Idex Страницы: 14

ARO PF20 B Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: KNF Страницы: 56

HEATSEEKER VORTEXE

Бренд: Supreme Heating Страницы: 34

Бренд: Graco Страницы: 14

Masterflex L/S 77390-00

Бренд: Cole Parmer Страницы: 15

Бренд: Carrier Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды