ITT HT 3196 i-FRAME Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 148

background image

a) Install the shaft sleeve.
b) Thread the impeller on the shaft until hand tight.
c) Rotate the shaft 360º.
d) If the total indicator reading is greater than 0.002 in. (0.051 mm), then disassemble the shaft sleeve

and determine the cause.

e) Remove the impeller and shaft sleeve.

SCALE

0.150

4. Check the frame-face runout by rotating the shaft so that the indicator measures the fit for 360º.

If the total indicator reading is greater than 0.001 in. (0.025 mm), then disassemble and determine the
cause.

5. Place the manila gasket (360D) on the frame (228), and hold the gasket in place by inserting the dowel

pins (469B) in their holes.
The gasket is designed to fit only one way.

6. Install the frame adapter.

a) Place the frame adapter (108) onto the frame assembly.
b) Align the bolt holes and dowel locations on the frame adapter with the bolt holes and dowel

locations on the frame.

Maintenance

106

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
106
107
108
109
110
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Galmet Страницы: 256

Бренд: EAS Electric Страницы: 165

Бренд: salmson Страницы: 16

Бренд: ubbink Страницы: 29

Бренд: YANGTECH Страницы: 23

Бренд: Daikin Страницы: 60

PacificHydrostar 2" Gasoline Powered Clear Water...

Бренд: Pacific hydrostar Страницы: 24

Бренд: Cordivari Страницы: 44

Бренд: Tiger Страницы: 36

Aqua-Pure 3MFF100

Бренд: 3M Страницы: 8

Бренд: BLACKMER Страницы: 14

Бренд: Wacker Neuson Страницы: 50

Бренд: Daikin Страницы: 44

Бренд: DROPSA Страницы: 14

AQUARAIN RJ 5.60.1M

Бренд: OLIJU Страницы: 24

Бренд: A.O. Smith Страницы: 18

Бренд: Daikin Страницы: 300

Бренд: TOHATSU Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды