ITT HT 3196 i-FRAME Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 148

background image

228A

134

370D

423

370C

4. Remove the jack screws (370D) with nuts (423).
5. Remove the bearing housing O-ring (496) and the bearings.
6. Remove the outboard bearing retaining snap ring (361A).

370D 423

134

361A

168A

496

7. Remove the bearing housing (134) and bearings (112A and 168A) from the shaft (122).

134

112

361A

168A

122

8. Remove the bearing locknut (136) and bearing lock washer (382).
9. Remove the inboard bearing (168A).
10. Remove the outboard bearing (112A).

NOTICE: Use force only on the inner race when you press bearings off the shaft. Do not use force
in situations in which you might break a part. Doing so may result in equipment damage.

NOTICE:
Save the bearings for inspection. Do not reuse the bearings. Doing so may result in decreased
performance.

Maintenance

74

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
74
75
76
77
78
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Makita Страницы: 96

Бренд: Ebsray Страницы: 12

Бренд: VARISCO Страницы: 16

Бренд: Magnum Страницы: 16

45 E Frame Series

Бренд: Danfoss Страницы: 44

ElectriFLEX LD LE Series

Бренд: Bradford White Страницы: 40

Бренд: Wacker Neuson Страницы: 72

Бренд: Mixtron Страницы: 44

Бренд: Pearl Страницы: 6

Бренд: Wacker Neuson Страницы: 60

Sherpa Monobloc 4

Бренд: Olimpia splendid Страницы: 96

Бренд: Fairland Страницы: 29

SKS 1000 Series

Бренд: Pentair Jung Pumpen Страницы: 12

Basic Line BS 7010

Бренд: WATERKOTTE Страницы: 60

Бренд: Boschetti Industrie Meccaniche Страницы: 24

Бренд: Watts Страницы: 16

FLOJET G257 Series

Бренд: Xylem Страницы: 4

Бренд: Dantherm Страницы: 308

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды