ITT HT 3196 i-FRAME Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 148

background image

109A

371C

360C

134

8. Install the inboard bearing as follows (see the illustration):

a) Coat the inner surfaces of the bearings with lubricant.
b) Put the inboard bearing (168) onto the shaft (122).

The regreasable bearing has a single shield. Make sure that the bearing is installed with the shield
away from the impeller.

122

168A

9. Install the remaining parts onto the bearing shaft as follows (see the illustration):

a) Install a new O-ring (496).
b) Install the outboard labyrinth oil-seal (332A) into the end cover (109A).

Place the drain slots of  the oil seal at the bottom position (6 o’clock).
Make sure that the edges of  the keyway are free from burrs. To protect the O-ring, cover the
keyway lengthwise with a piece of  electrical tape before you install the oil seal.

332A

109A

496

10. Install the shaft assembly into the bearing frame as follows (see the illustration):

a) Coat the outside of the bearing housing (134) with oil.
b) Coat all the internal surfaces of the bearing frame (228) with oil.
c) Install the shaft assembly into the bearing frame (228).

Make sure that the shaft rotates freely.

d) Install the clamp bolts (370C) in the bearing housing (134) and tighten by hand.
e) Install the jack bolts (370D) with the locknuts (423) in the bearing housing (134) and tighten by

hand.

f) Attach the bearing-frame foot (241) and fasten the bolts (370F) by hand.

Maintenance

104

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
104
105
106
107
108
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Parker Страницы: 44

Бренд: Gardena Страницы: 16

Water Solutions 3098 Series

Бренд: Zoeller Страницы: 4

Aquanot Spin 508

Бренд: Zoeller Страницы: 2

Бренд: Zoeller Страницы: 11

Бренд: Zip Страницы: 18

Бренд: AquaPRO Страницы: 4

Бренд: Gorenje Tiki Страницы: 152

Бренд: Carrier Страницы: 12

Бренд: Waterax Страницы: 6

EASYDOS Peristaltic V

Бренд: Jesco Страницы: 20

Бренд: AquaScape Страницы: 16

MICROPUMP 668-400-2

Бренд: Idex Страницы: 33

Бренд: Wayne Страницы: 12

HWW 4600 NIRO-NIRO

Бренд: EINHELL Страницы: 40

tubra- PGS multi

Бренд: Tuxhorn Страницы: 60

ARO PF20 B Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: KNF Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды