ITT HT 3196 i-FRAME Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 148

background image

Place a small magnet on the condition monitor over the ITT logo and then remove it, as this example
shows.

Magnet

761B

When the condition monitor is activated it:
1. Displays a series of red LEDs followed by a solid green LED.
2. Collects eight samples that are spaced one second apart.
3. Averages these readings to establish the baseline vibration level.
4. Flashes a green LED after approximately twelve seconds.
For the first ten minutes, the green LED flashes every second for five consecutive flashes and then
pauses to take a vibration reading. More frequent measurements (every six seconds) are taken in this
startup period so that an alarm can be immediately detected.

i-ALERT

™

Condition Monitor routine operation

Measurement interval

This table shows the measurement intervals for the condition monitor during normal operation and when
the monitor is in alarm mode.

Mode

Measurement interval

Normal operating mode

Five minutes

Alarm mode

Two minutes

When the condition monitor measures a reading beyond the specified temperature and vibration limits, the
appropriate red LED flashes. After the process or pump condition that causes the alarm is corrected, the
condition monitor returns to normal mode after one normal-level measurement.

Alarm mode

When the condition monitor is in alarm mode, you should investigate the cause of the condition and make
necessary corrections in a timely manner.

Magnetic device considerations

Be careful when you use magnetic devices in close proximity of the condition monitor, such as magnetic
vibration-monitoring probes or dial indicators. These magnetic devices can accidentally activate or
deactivate the condition monitor resulting in improper alarm levels or loss of monitoring.

Commissioning, Startup, Operation, and Shutdown

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

57

«
...
57
58
59
60
61
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: Calpeda Страницы: 80

Бренд: TapFlo Страницы: 42

Бренд: Barnes Страницы: 20

Бренд: Daikin Страницы: 17

Бренд: Daikin Страницы: 30

Fybroc series 1530

Бренд: Met-Pro Страницы: 22

Бренд: Nortek Страницы: 52

ecoTOUGH NRC111-DV-LP

Бренд: Noritz Страницы: 32

Бренд: Zodiac Страницы: 36

JSV3H60-E5 230/1

Бренд: GORMAN-RUPP PUMPS Страницы: 34

Бренд: Comet Страницы: 12

HTVZD*1C series

Бренд: Halsey Taylor Страницы: 7

Hydra-Cell G-25

Бренд: Wanner Engineering Страницы: 20

Бренд: Giant Страницы: 8

Бренд: emaux Страницы: 21

Бренд: Quincy Compressor Страницы: 42

Бренд: Klima hitze Страницы: 39

THERMOSIPHON 150/2.5

Бренд: SUN&HEAT Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды