ITT HT 3196 i-FRAME Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 148

background image

Install the pump, driver, and coupling

1. Mount and fasten the pump on the baseplate. Use applicable bolts.
2. Mount the driver on the baseplate. Use applicable bolts and hand tighten.
3. Install the coupling.

See the installation instructions from the coupling manufacturer.

Pump-to-driver alignment

Precautions

WARNING:

• Follow shaft alignment procedures in order to prevent catastrophic failure of drive components or

unintended contact of rotating parts. Follow the coupling installation and operation procedures from
the coupling manufacturer.

• Always disconnect and lock out power to the driver before you perform any installation or

maintenance tasks. Failure to disconnect and lock out driver power will result in serious physical
injury.

NOTICE: Proper alignment is the responsibility of the installer and the user of the unit. Check the
alignment of frame-mounted units before you operate the unit. Failure to do so can result in equipment
damage or decreased performance.

Alignment checks

When to perform alignment checks

You must perform alignment checks under these circumstances:

• The process temperature changes.
• The piping changes.
• The pump has been serviced.

Types of alignment checks

Type of check

When it is used

Initial alignment (cold alignment)

check

Prior to operation when the pump and the driver are at ambient

temperature.

Final alignment (hot alignment)

check

After operation when the pump and the driver are at operating

temperature.

Initial alignment (cold alignment) checks

When

Why

Before you grout the baseplate

This ensures that alignment can be accomplished.

After you grout the baseplate

This ensures that no changes have occurred during the grouting

process.

After you connect the piping

This ensures that pipe strains have not altered the alignment.
If changes have occurred, you must alter the piping to remove pipe

strains on the pump flanges.

Installation

28

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
28
29
30
31
32
...
»

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Бренд: abc Страницы: 8

Бренд: Wacker Neuson Страницы: 46

EcoPart 400 230V 1N~

Бренд: CTC Union Страницы: 40

PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float...

Бренд: Pacific hydrostar Страницы: 9

Бренд: Barmesa Pumps Страницы: 10

Бренд: Wayne Страницы: 12

Pneumatic Oilpump 3:1

Бренд: Pressol Страницы: 28

Бренд: Little Giant Страницы: 12

Basic Line BS 7010

Бренд: WATERKOTTE Страницы: 60

Бренд: Rolair Страницы: 5

Бренд: INOXPA Страницы: 28

Бренд: German pool Страницы: 10

Бренд: vacuubrand Страницы: 75

Бренд: Sunsystem Страницы: 24

Econoboil 301642

Бренд: Zenith Страницы: 12

Бренд: Bradford White Страницы: 54

Бренд: DGFLOW Страницы: 4

Бренд: STIEBEL ELTRON Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды