manualshive.com logo in svg

ITT HT 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

ITT HT 3196 i-FRAME - надежный и эффективный насос с высокой производительностью. Установите, работайте и поддерживайте его с помощью инструкции по монтажу, эксплуатации и техническому обслуживанию, которую можно бесплатно скачать с manualshive.com. Надежный помощник в вашем производстве.

Поделиться
Скачать
background image

Table of Contents

Introduction and Safety...................................................................................................................................................4

Introduction.......................................................................................................................................................................4

Requesting other information......................................................................................................................................4

Safety...................................................................................................................................................................................4

Safety terminology and symbols..................................................................................................................................5
Environmental safety.....................................................................................................................................................6
User safety.......................................................................................................................................................................6
Safety regulations for Ex-approved products in potentially explosive atmospheres...........................................8

Product approval standards.............................................................................................................................................9
Product warranty.............................................................................................................................................................10

Transportation and Storage..........................................................................................................................................11

Inspect the delivery.........................................................................................................................................................11

Inspect the package.....................................................................................................................................................11
Inspect the unit.............................................................................................................................................................11

Transportation guidelines...............................................................................................................................................11

Pump handling.............................................................................................................................................................11
Lifting methods............................................................................................................................................................11

Storage guidelines............................................................................................................................................................13

Pump storage requirements........................................................................................................................................13
Frostproofing................................................................................................................................................................13

Product Description........................................................................................................................................................14

General description HT 3196 .......................................................................................................................................14

Part description HT 3196...........................................................................................................................................15

General description i-ALERT

™

 Condition Monitor................................................................................................16

Nameplate information..................................................................................................................................................17

Installation.........................................................................................................................................................................20

Preinstallation...................................................................................................................................................................20

Pump location guidelines............................................................................................................................................20
Foundation requirements............................................................................................................................................21

Baseplate-mounting procedures....................................................................................................................................21

Prepare the baseplate for mounting..........................................................................................................................21
Install the baseplate using shims or wedges.............................................................................................................22
Install the baseplate using jackscrews.......................................................................................................................22
Install the baseplate using spring mounting.............................................................................................................24
Install the baseplate using stilt mounting.................................................................................................................25
Baseplate-leveling worksheet......................................................................................................................................27

Install the pump, driver, and coupling.........................................................................................................................28
Pump-to-driver alignment..............................................................................................................................................28

Alignment checks.........................................................................................................................................................28
Permitted indicator values for alignment checks....................................................................................................29
Alignment measurement guidelines..........................................................................................................................29
Attach the dial indicators for alignment...................................................................................................................29
Pump-to-driver alignment instructions....................................................................................................................30
C-face adapter...............................................................................................................................................................33

Grout the baseplate.........................................................................................................................................................33
Piping checklists..............................................................................................................................................................34

General piping checklist..............................................................................................................................................34
Suction-piping checklist..............................................................................................................................................36
Discharge piping checklist..........................................................................................................................................38

Table of Contents

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

1

Содержание HT 3196 i-FRAME





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT 3196 i-FRAME

Haier Little Sea-ox FCD-30 Manual preview
Little Sea-ox FCD-30
Бренд: Haier Страницы: 23
Palm H Series Installation And Operation Manual preview
H Series
Бренд: Palm Страницы: 20
Bard CH Series Installation Instructions Manual preview
CH Series
Бренд: Bard Страницы: 50
Makita PF400MP Instruction Manual preview
PF400MP
Бренд: Makita Страницы: 96
A.O. Smith ProMax GCV-30 Specification Sheet preview
ProMax GCV-30
Бренд: A.O. Smith Страницы: 2
A.O. Smith Residential Gas Water Heaters Instruction Manual preview
Residential Gas Water Heaters
Бренд: A.O. Smith Страницы: 84
PSG Dover WILDEN P100 Advanced Plastic Engineering, Operation & Maintenance preview
WILDEN P100 Advanced Plastic
Бренд: PSG Dover Страницы: 28
Waterous S200-P Series Operation And Maintenance Instructions preview
S200-P Series
Бренд: Waterous Страницы: 10
Pattfield Ergo Tools PE-SW 3030 Original Instructions Manual preview
PE-SW 3030
Бренд: Pattfield Ergo Tools Страницы: 162
Bayrol Auromatic Salt Instructions For Use Manual preview
Auromatic Salt
Бренд: Bayrol Страницы: 56
A.O. Smith Cyclone Xi Service Handbook preview
Cyclone Xi
Бренд: A.O. Smith Страницы: 43
Durapac DPR-223 Instruction Manual preview
DPR-223
Бренд: Durapac Страницы: 11
KNF N630.12 Translation Of Original Operating And Installation Instructions preview
N630.12
Бренд: KNF Страницы: 88
Davey DynaDrive DD60-10 Installation And Operating Instructions Manual preview
DynaDrive DD60-10
Бренд: Davey Страницы: 32
P.Lindberg 9027885 Manual preview
9027885
Бренд: P.Lindberg Страницы: 54
Wilden Original PX15 Operation & Maintenance Manual preview
Original PX15
Бренд: Wilden Страницы: 39
Daesung Celtic SHW-13 Installation Manual And Owner'S Manual preview
SHW-13
Бренд: Daesung Celtic Страницы: 62
Goodman GSZ11 Repair Parts preview
GSZ11
Бренд: Goodman Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды