ITT HT 3196 i-FRAME Скачать руководство пользователя страница 41

Страница: 41 / 148

Check

Explanation/comment

Checked

Check that a check valve is installed in

the discharge line, between the

isolation valve and the pump

discharge outlet.

The location between the isolation valve and the

pump allows inspection of the check valve.
The check valve prevents damage to the pump and

seal due to the back flow through the pump, when

the drive unit is shut off. It is also used to restrain

the liquid flow.
See Example: Discharge piping equipment for

illustrations.

If increasers are used, check that they

are installed between the pump and

the check valve.

See Example: Discharge piping equipment for

illustrations.

If quick-closing valves are installed in

the system, check that cushioning

devices are used.

This protects the pump from surges and water

hammer.

Example: Discharge piping equipment

Correct

Incorrect

Bypass line

Shut-off valve

Check valve

Discharge isolation valve

Check valve (incorrect position)

The isolation valve should not be positioned
between the check valve and the pump.

Installation

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание HT 3196 i-FRAME





















































































































































Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT HT 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HT 3196 i-FRAME

Отзывы:

Похожие инструкции для HT 3196 i-FRAME

Бренды по названию

Популярные бренды